Ticket

zurück zur Ticket Übersicht

Projekt RCM Ultimate
Zusammenfassung Unable to split laps en
Sequenz 3938
Klassifikation Bug
Priorität Low
Status Done
Startdatum 30.12.1899
Fälligkeitsdatum 30.12.1899
Verantwortlich
Version 2.5.5.2262
Aufwand 0
Beschreibung Last weekend we ran a race. One rider had a lap that was not counted correctly. I normally correct this afterwards by splitting the lap in question into 2 laps. However, this was not possible last weekend.

Actions I perform:
Heat confirmation undo. I select the driver in question, right-click, corrections -> Lap times.

Then I can increase the "Split lap time in number of laps" to e.g. 2 And then also see the lap time jump (split in 2 laps, lap time by half). Only I cannot click "OK", the button remains grayed out. The Cancel button does work normally.

At the edit lap option is also strange behavior. Heat confirmation undo. I choose a rider, right click, corrections -> Edit lap I can adjust the lap time, but again the OK button remains grayed out, and the cancel button does not work either.
If you press the cancel button, then very quickly the value in the field where you can adjust it jumps back to the original value.

It looks like the focus goes wrong somewhere. However, only the timekeeping window in RCM was open for the heat in question.

In the attachment the relevant window and the OK button that could not be clicked.

After the race I ran another test with the decoder simulator. However, this still gave the same problem.

Betreft RCM software versie: v2.5.4.2107 [15.04.2025]
Database version: v181 [20-3-2025]
Configuration version: v120 [20-3-2025]

Kommentare

Zeitstempel Wer Kommentar
07.07.2025 15:30:47 Felix Romer Attached to this email is the export of the event.
Also a screenshot from the heat of the pilot, with round times.
The round time of 1:20:87 is the one I tried to split.

Section: Club - 1/8 Buggy
Heat: 1 (kwalificatie 1 (qualification 1)
Pilot: Simon van der Vleuten
Lap: 1 (first one counted, 1:20:87)

Key: 35951
Seq. nr: 32003

Also checked afterwards with a (offline) test event.
Did a heat with de decoder simulator, which gave the same result.
I was unable to split any of the rounds.

Change history

Zeitstempel Wer Änderung
03.07.2025 19:43:58 Ticket erstellt
04.07.2025 07:19:42 Felix Romer Feld: Responsible
Alter Wert: -
Neuer Wert: Romer Felix
04.07.2025 07:19:42 Felix Romer Feld: Status
Alter Wert: Opened
Neuer Wert: Running
04.07.2025 07:20:39 Felix Romer Feld: Specification
Alter Wert: Betreft RCM software versie: v2.5.4.2107 [15.04.
2025]
Database version: v181 [20-3-2025]
Configuration version: v120 [20-3-2025]

Afgelopen weekend hebben we een wedstrijd verreden.
Hierbij had een rijder een ronde die niet goed geteld werd.
Dit doe ik normaal gesproken achteraf corrigeren door de bewuste ronde op te splitsen in 2 rondes.
Echter was dit afgelopen weekend niet mogelijk.

Acties die ik uitvoer:
Heat bevestiging ongedaan maken.
Ik kies de bewuste rijder, rechtermuisklik, correcties -> Rondetijden

Vervolgens kan ik wel de "Split lap time in number of laps" ophogen naar bv. 2
En zie dan ook de ronde tijd verspringen (split in 2 rondes, rondetijd door de helft)
Ik kan alleen niet op "OK" klikken, de knop blijft grayed out.
De Annuleer knop werkt wel normaal.

Bij de bewerk ronde optie is ook vreemd gedrag.
Heat bevestiging ongedaan maken.
Ik kies een rijder, rechtermuisklik, correcties -> Bewerk ronde
Ik kan de ronde tijd aanpassen, maar ook hier blijft de OK knop greyed out, en werkt de annuleer knop ook niet.
Druk je op de annuleer knop, dan verspringt zeer snel de waarde in het veld waarin je die kan aanpassen terug naar de originele waarde.

Het lijkt er op dat de focus ergens verkeerd gaat.
Echter stond alleen het venster in RCM open van de tijdwaarneming van de bewuste heat.

In de bijlage het bewuste venster en de OK knop die niet aan te klikken was.

Na de wedstrijd heb ik nu nog een test uitgevoerd met de decoder simulator. Dit gaf echter nog steeds hetzelfde euvel.
Neuer Wert: Last weekend we ran a race. One rider had a lap that was not counted correctly. I normally correct this afterwards by splitting the lap in question into 2 laps. However, this was not possible last weekend.

Actions I perform:
Heat confirmation undo. I select the driver in question, right-click, corrections -> Lap times.

Then I can increase the "Split lap time in number of laps" to e.g. 2 And then also see the lap time jump (split in 2 laps, lap time by half). Only I cannot click "OK", the button remains grayed out. The Cancel button does work normally.

At the edit lap option is also strange behavior. Heat confirmation undo. I choose a rider, right click, corrections -> Edit lap I can adjust the lap time, but again the OK button remains grayed out, and the cancel button does not work either.
If you press the cancel button, then very quickly the value in the field where you can adjust it jumps back to the original value.

It looks like the focus goes wrong somewhere. However, only the timekeeping window in RCM was open for the heat in question.

In the attachment the relevant window and the OK button that could not be clicked.

After the race I ran another test with the decoder simulator. However, this still gave the same problem.

Betreft RCM software versie: v2.5.4.2107 [15.04.2025]
Database version: v181 [20-3-2025]
Configuration version: v120 [20-3-2025]
29.07.2025 07:52:44 Felix Romer Feld: Version
Alter Wert:
Neuer Wert: 2.5.5.2262
29.07.2025 07:52:48 Felix Romer Feld: Status
Alter Wert: Running
Neuer Wert: Done